How deep should a footing be for a light pole?
Table of Contents
Most pole standard bases in commercial and retail parking areas are a minimum 6′ deep and they are usually 8′ deep. As far as a concrete pole pier this usually has to be worked out by a structural engineer familiar to you area.
How deep do you bury a light pole?
Lamp posts typically require using concrete for stability and support. However, if you’re trying to install a temporary lamp post, here’s how to do it without without using concrete. Dig a hole that is 18- to 24-inches deep and 6 inches in diameter.
How much are concrete light poles?
The average street light pole cost ranges from $2,000 to $3,000, not including installation. The installation cost depends on the city, but the average is somewhere around $1,000.
How do you calculate light pole foundation?
Measure the circumference of the light pole in inches as close to the base as possible. For example, the circumference might be 40 inches. Divide the circumference by 2 times the number pi to get the radius of the base. Use 3.14 for the number pi.
How deep is a 20ft pole?
Typically you’d embed a pole at a ratio of 1:4. In your case, if the poles are 20′ above ground, you’d want to be 4-5 feet down. If your poles are 20′ in length (16-17′ above ground), 3-4′ may be adequate.
How much of a pole should be in the ground?
Poles are typically set into the ground: 10% of the overall height + 2 feet, except in questionable soil conditions. Example: Overall pole height: 30 feet, the pole should be buried: 3 feet + 2 feet = 5 feet below grade, and 25 feet above grade. Note: always consult an engineer and review the soils report.
How much is a power pole?
VERY rough numbers – commonly about $5-10/LF for overhead runs (meaning new poles typically every 100-300 feet, possibly more in high tree area), plus $500-3000 per pole needed depending on length (probably about 36-40′ tall minimum for your area if not rural but can be much more in heavily treed areas, so closer to …
How much does it cost to repair a light pole?
the estimated cost of a street light pole is US$2000 to US$3000, with electrician cost to put in street light to installation is up to $1000! If your project is for the highway or bridge, the total cost will raise by 20% more.
How much does a street light pole weigh?
Ordering more than 10? Request a quote and we’ll back to you with our lowest price.
| Type of Area | Pole / Street / Parking Lot |
|---|---|
| Handhole Size | 2 x 4 |
| Pole Height | 30′ Ft |
| Pole Weight | 223 lbs. |
| Pole Width | 6″ x 6″ |
How do you find the moment of a pole?
Foundation Detail:
- Total Weight =Pole Weight +Foundation Weight.
- Total Weight = 241 +(0.7×0.7×1.95×2500) =2620.75 Kg.
- Stabilizing Moment = Total Weight X (Foundation Length/2)
- Stabilizing Moment = 2620.75 X (0.7/2) = 920.41 Kg/Meter.
How do you raise a heavy pole?
lift pole with jack, bring second jack as far down on the pole as possible and start lifting, repeat. The guide wires will keep the pole from moving left or right once it’s high enough you can no longer reach it.
How long does a power pole last?
An Electric Power Research Institute study suggested that wood poles lasted 50 years. Most utilities assume that their poles provide 30 to 40 years of service life.
What do you need to fix a broken light pole?
Anchor Bolt Adapters to correct misaligned anchor bolts and light pole base plates. Pole repair kits to avoid light pole replacement by repairing rusted light poles. Universal locking hand hold cover to prevent copper wire theft.
What is included in light pole maintenance and inspection?
Light pole maintenance and inspection should consist of — but not be limited to — the following: Visually inspect pole shaft for areas of rust, corrosion, and any dents or signs that the structural integrity has been compromised. Visually inspect brackets, arms, luminaires, and welds to ensure there is no metal fatigue.
Why do light pole bases get damaged so quickly?
Here’s why: Most traditional light pole bases have seams and the interior lacks powder coating or an enamel finish. As a result, salts and moisture can seep inside and lead to corrosion. Hence, why it’s so common to see light pole base damage before the rest of the lamppost appears worn.
Why choose iLight pole systems?
Light Pole Systems offers innovative and unique products designed to enhance safety, fight copper-wire theft and save money. We pride ourselves on providing excellent service and look forward to helping you with your copper wire theft and light pole repair needs.